MDF V313 – humidity resistant – lightweight
FIBRABEL MR / Umidax L
V313 CARB II through-coloured green Type L-MDF-H nach DIN EN 622-5 Datenblatt zum Download
approx. 600 kg/m3 bulk density
Area of application
Damp-resistant lightweight MDF for general non-bearing use in humid environments.
MDF with low density and with a hard, finely sanded surface and a well screw-mountable core, glued with MUF glue. The board is subject to only minimum expansion and swelling even with high humidity and is suitable for general, non-bearing applications in humid environments. MDF Umidax® L can be finished with paper, melamine, veneer, composite lay-ups and varnish. The boards are made of 100 % coniferous wood and do not have any coarse fibres on the surface. The boards are excellent to mill and emit low quantities of formaldehyde (class A).
Using the product
The boards must be used only according to use class 1 (restrictions for ambient temperature and humidity) and hazard classes 1 and 2, EN 335-3. The boards must not have direct contact with water during and especially after installation. Any stacking must be done quickly on a pallet or with a sufficient number of crossbeams. Boards must not be stored upright unless floor contact can be ruled out. With fluctuating humidity conditions, the boards expand or shrink; however, to a lesser extent than S-Lux MDFs. A margin for expansion must therefore always be provided for. Use suitable tools for sawing, milling and drilling. MDF Umidax® L can be used for walls and interior decoration. A corrosion resistant metal fitting, e.g. galvanized steel, must be used in use class 2. Nails or screws must have a distance of at least 8 mm to the edge of the board.
Dimensions and stock program
Thickness: 12 to 38 mm. Max. width and length: 244–255 to 635 cm. Spanolux has high capacity saws and can provide all dimensions. The pressing capacities generally enable delivery of all thicknesses, lengths and widths.
|in mm||in mm|
|1220 x 2440||1220 x 3050||1300 x 3050|
Refer to the individual items for details on packaging units in pcs.
You can find the data sheet with technical details in the Downloadcenter.
|General properties + standard||Unit||Average values|
|Thickness EN 324-1||mm||12||15||16||18||19||22||38|
|Thickness EN 323||Kg/m³||640||610||610||610||610||610||610|
|Moisture content EN 322||%||6-10||6-10||6-10||6-10||6-10||6-10||6-10|
|Technical properties + standard||5/95 quantile values|
|Swelling/24u EN 317||%||16||13||13||13||13||12||11|
|Tensile strength EN 319||N/mm²||0,45||0,45||0,45||0,45||0,45||0,45||0,4|
|Bending strength EN 310||N/mm²||20||18||18||18||18||16||16|
|Bending elasticity modulus EN 310||N/mm²||1700||1600||1600||1600||1600||1500||1400|
|Swelling after cycle test EN 321 option 1||%||16||15||15||15||15||15||15|
|Tensile strength after cycle test EN 321 option 1||N/mm²||0,25||0,2||0,2||0,2||0,2||0,15||0,1|
Fibreboard specificationsPart 1: General requirements
|Nominal diameter classes (mm)|
|Tolerances with nominal dimensions:|
|Thickness||EN 324-1||mm||± 0,2||± 0,3|
|Length and width||EN 324-1||mm/m||± 2,0 mm/m, max. ± 5,0 mm|
|Perpendicularity||EN 324-2||mm/m||2,0 mm/m|
|Deviations from the straightness of length and width||EN 324-2||mm/m||1,5 mm/m|
|Tolerance for board thickness||EN 323||%||± 7,0|
|Formaldehyde perforator class E1||EN 120||mg/100g||8|
UMIDAX® L MDFs meet the defaults of EN 622-5, option 1, cycle test, whereby the boards are immersed in water, frozen and finally dried. This cycle is repeated three times. After that, the test items are tested for swelling and transverse tensile strength. The boards are checked by our own laboratory daily and have the EU label.